Support

Practise Information technology Yourself - Model Due south

Tesla owners who wish to perform basic procedures or maintenance on their Model S can practice then without having to schedule a service date. Just perform a procedure if you feel comfy doing and then, and always follow all provided instructions.

For answers to further questions, visit the Back up page.

  • Restarting the Touchscreen
  • Ability Cycling the Vehicle
  • Pairing a Bluetooth Device
  • Connecting to Wi-Fi
  • Programming HomeLink®
  • Adding and Removing Keys
  • Replacing the Key Fob Battery
  • Unlocking and Starting Your Vehicle Using the Tesla App
  • Replacing the Cabin Air Filters
  • Checking and Adjusting Tire Pressures
  • Drive to Calibrate Cameras
  • Replacing Hood Struts
  • Topping Upward Windshield Washer Fluid
  • Replacing Wiper Blades
  • Manually Releasing Accuse Cable
  • Opening Hood with No Power
  • Jump Starting the Low Voltage Battery
  • Adjusting Liftgate Opening Height
  • Charge Port Status Lights
  • Gen 2 Mobile Connector Condition Lights
 

Restarting the Touchscreen

You tin can restart your touchscreen if it is unresponsive or demonstrates unusual beliefs.

Note: To ensure the condom of occupants likewise every bit other road users, restart the touchscreen simply when the vehicle is in Park.

To restart the touchscreen on Model S, follow these steps:

  • Shift into Park.
  • Hold down both whorl buttons on the steering yoke until the touchscreen turns black.
  • After a few seconds, the Tesla logo appears. Wait approximately xxx seconds for the touchscreen to restart.

If the touchscreen is still unresponsive or demonstrating unusual behavior after a few minutes, effort power cycling the vehicle. See Power Cycling the Vehicle.

Note: Restarting the touchscreen as well activates the bulldoze manner selector on the center panel.

Note: Restarting the touchscreen using the gyre buttons does not ability Model Southward off and on.

Dorsum to Elevation

 

Power Cycling the Vehicle

You can power cycle Model S if it demonstrates unusual behavior or displays a nondescript alert. To power wheel Model Due south, follow these steps:

  • Shift into Park.
  • On the touchscreen, touch on 'Controls' > 'Rubber' > 'Power Off.'
  • Look for at least 2 minutes without interacting with the vehicle. Exercise non open up the doors, touch the brake pedal, touch on the touchscreen, etc.
  • After two minutes, press the brake pedal or open the door to wake the vehicle.

Back to Peak

 

Pairing a Bluetooth Device

Pairing allows you to use your Bluetooth-capable mobile device hands-free to make and receive telephone calls, access your contact list, view your recent calls, etc. Information technology likewise allows you lot to play media files from your device. Once a device is paired, Model S can connect to it whenever the device is within range.

To pair a Bluetooth device, follow these steps while sitting inside Model S:

  • Ensure both the touchscreen and the mobile device are powered on.
  • On your device, enable Bluetooth and ensure information technology is discoverable.
    Note: On some devices, this may require you to become to Bluetooth Settings for the remainder of the procedure.
  • Touch the Bluetooth icon on the top of the touchscreen.
  • On the touchscreen, bear on 'Add New Device' > 'Start Search.' The touchscreen displays a list of all bachelor Bluetooth devices within operating distance.
  • On the touchscreen, bear upon the device with which you want to pair. Within a few seconds, the touchscreen displays a randomly generated number, and your device should brandish the same number.
  • Check that the number displayed on your device matches the number displayed on the touchscreen. Then, on your device, ostend that you lot want to pair.
  • If prompted on your device, specify whether you desire to allow Model S to access your contacts and media files.

When paired, Model S automatically connects to the device, and the touchscreen displays the Bluetooth symbol next to the device's proper noun to bespeak that the connection is active.

At whatever time, you can display the Bluetooth settings screen to modify settings associated with a connected device. For example, yous can designate a continued phone every bit the 'Priority Device.' This is useful in situations where y'all have continued more than one device, and both devices are frequently used in Model Southward at the same time. Model South automatically attempts to connect to the priority device earlier others.

Dorsum to Top

 

Connecting to Wi-Fi

Wi-Fi is available as a information connection method and is oft faster than cellular data networks. Connecting to Wi-Fi is specially useful in areas with limited or no cellular connectivity. To ensure fast, reliable delivery of software and map updates, Tesla recommends leaving Model S connected to a Wi-Fi network whenever possible (for instance, when parked overnight).

To connect Model Due south to a Wi-Fi network, follow these steps:

  • Touch 'Controls' > Wi-Fi icon at the top of the 'Controls' screen. Model S begins to scan and display detected Wi-Fi networks that are within range.
    Note: If a known Wi-Fi network does not appear in the list, move Model Southward closer to the access indicate or consider using a range extender.
  • Select the Wi-Fi network you want to use, enter the password (if necessary), and so touch 'Confirm.'
  • Model S connects to the Wi-Fi network. Whenever the network is within range, Model S connects to information technology automatically.

Y'all can also connect to a hidden network that isn't shown on the list of scanned networks. Just affect 'Wi-Fi Settings,' enter the name of the network in the resulting dialog box, select the security setting, then touch 'Add Network.'

Note: If more than 1 previously connected network is within range, Model S connects to the one about recently used.

Note: At Tesla Service Centers, Model South automatically connects to the Tesla Service Wi-Fi network.

Hotspots and Connectivity

You tin also use a mobile hotspot or your phone's internet connectedness via Wi-Fi tethering (subject to fees and restrictions of your mobile carrier) to access the internet. To remain connected to Wi-Fi when shifting into Bulldoze or Reverse, choose the connection from the Wi-Fi settings screen, then touch 'Remain connected in Drive.'

Back to Top

 

Programming HomeLink®

To program HomeLink® in Model S, follow these steps:

  • Park Model South so that the front bumper is in forepart of the device you want to programme.

    Circumspection: Your device might open up or close during programming. Therefore, before programming, make sure that the device is articulate of any people or objects.

  • Cheque that the device'southward remote control has a good for you battery. Tesla recommends replacing the battery in the device'south remote command before programming HomeLink.
  • Touch the HomeLink icon at the top of the 'Controls' screen.
  • Touch 'Create HomeLink.'
  • Select the way you lot wish to use: Standard, D-Mode, or UR-Mode.
  • On the touchscreen, enter a name for your device, and then affect 'Enter' or 'Create HomeLink.'
  • Touch on 'Start' and follow the on-screen instructions.
    Note: If you run into a screen called 'Train the receiver' while programming the device, remember that this is a time-sensitive step. After pressing the Learn/Programme/Smart button on the device's remote command, y'all have only approximately thirty seconds to return to your vehicle and press 'Continue,' so press the trained HomeLink device name twice. Consider having an assistant to ensure yous can complete this step within xxx seconds.
  • Once your device is programmed, touch 'Salvage' to complete the programming.
  • Ensure HomeLink works equally expected. In some cases, you may need to repeat the programming process multiple times before succeeding.

Once programmed, y'all can operate the device by touching its corresponding HomeLink icon on the touchscreen. HomeLink remembers the location of your programmed devices. When yous approach a known location, the HomeLink control on the touchscreen automatically appears. When y'all drive away, it disappears.

Note: For additional assistance or compatibility questions, contact HomeLink past visiting the HomeLink website or calling ane-800-355-3515.

Dorsum to Top

 

Adding and Removing Keys

To add together a new key menu or central flim-flam to Model South, follow these steps:
Notation: When adding a key pull a fast one on, ensure it is at room temperature. Pairing a key fob that is very cold tin exist unsuccessful.

  • On the touchscreen, touch 'Controls' > 'Locks' then bear on '+' in the 'Keys' section.
  • Scan your new key menu or key pull a fast one on on the card reader located on the wireless phone charger. To scan the key play a joke on:
    • Place the key fob at the summit of the left telephone charger, against the heart divider.
    • Point the front of the key fob downwardly.
    • Swipe down (as shown in the prototype).
    When you lot hear a chime and the new fundamental is recognized, remove information technology from the menu reader.
  • Scan a key card or key fob that has already been paired to the vehicle to confirm new key pairing.
  • When complete, the cardinal list includes the new key. Touch on the associated pencil icon to customize the proper name of the central.

Y'all can purchase fundamental fobs in the Tesla Store.

When you no longer desire a key to access Model S (for example, you lost your mobile device or central card, etc.), remove it by following these steps:

  • On the touchscreen, touch 'Controls' > 'Locks.'
  • In the fundamental list, find the key that you would like to delete and touch its associated trash icon.
  • When prompted, scan an authenticated key carte or fundamental fob on the card reader to confirm the deletion. When complete, the key list no longer includes the deleted key.
Note: Model S requires at least one authenticated key card or key fob at all times. If only i fundamental card remains on the primal listing, you cannot delete it.

Dorsum to Peak

 

Replacing the Cardinal Fob Bombardment

Under normal utilize, the key fob has a battery that lasts for up to one year, depending on central play tricks version and selected vehicle settings. When the battery is low, a message displays on the touchscreen.

To replace the key fob bombardment, follow these steps:

  • With the central play a joke on placed button side down on a soft surface, release the bottom embrace, using a small-scale flat-bladed tool.
  • Remove the battery past lifting it away from the retaining clips.
  • While avoiding touching the battery'southward apartment surfaces, insert the new battery (type CR2330) with the '+' side facing up.

    Note: Wipe the battery make clean earlier fitting and avoid touching the bombardment's flat surfaces. Finger marks on the apartment surfaces of the battery can reduce battery life.

    Note: CR2330 batteries can be purchased from any retailer that sells batteries.

  • Holding the bottom cover at an angle, marshal the tabs on the cover with the respective slots on the key fob, then press the cover firmly onto the key play a joke on until it snaps into place.
  • Test that the key play a joke on works by unlocking and locking Model S.

Warning: Key fob batteries contain a chemical burn hazard and should not be ingested. The key fob contains a coin cell bombardment. If the coin jail cell battery is swallowed, it tin can cause astringent internal burns within two hours and can lead to expiry. Keep new and used batteries away from children. If the battery compartment does non shut securely, stop using the product and continue it away from children. If you lot think batteries might have been swallowed or placed inside any office of the body, seek immediate medical attending.

Dorsum to Top

 

Unlocking and Starting Your Vehicle Using the Tesla App

Yous tin can employ the Tesla app to unlock and commencement Model S. This may be useful in cases where you do not accept your key fob or are not physically close to the vehicle (for case, yous want to unlock the vehicle for your spouse from across town).

Note: Your mobile device and vehicle must both be actively continued to cellular service and mobile access must exist enabled on the touchscreen ('Controls' > 'Safe & Security' > 'Allow Mobile Access') to let the Tesla app to communicate with your vehicle. Tesla recommends that y'all e'er accept a functional concrete key readily available if parking in an area with limited or absent cellular service, such as an indoor parking garage.

To unlock Model Due south using the Tesla app, follow these steps:

  • Open the Tesla app on your device.
  • Touch 'Controls' > 'Unlock.'
  • Touch 'Yes' on the confirmation popup window.

To beginning Model S using the Tesla app, follow these steps:

  • Open the Tesla app on your device.
  • Bear upon 'Controls' > 'Offset.'
  • Enter your Tesla Business relationship password on the confirmation popup window.

Notation: Yous will have two minutes to start driving subsequently enabling keyless driving. If the ii-minute window has expired prior to driving you will need to re-enable keyless driving.

Dorsum to Superlative

 

Replacing Cabin Air Filters

Model Southward has an air filter that prevents pollen, industrial fallout, route dust, and other particles from entering the cabin through the vents. Tesla recommends replacing these filters every two years (every year in China). Cabin filters tin be purchased from the Tesla Shop.

To supercede the cabin filter in Model S, follow these steps:

  • Turn off the climate control system.
  • Remove the rear underhood apron.
  • Slowly and gently pull down the footwell cover to release the magnets, then disconnect the electrical harness on the right side of the cover. Set up the footwell cover bated.
  • Squeeze the cabin filter door lock to release it, then remove and set up the door aside.
  • Note the direction of air catamenia printed on the motel filter. The arrows on the filter should face toward the rear of the vehicle.
  • Slide the filter out of the HVAC module.
  • Ensuring that the arrows on the new filter face toward the rear of the vehicle, insert the new motel filter into the HVAC module.
  • Slide the motel filter door onto the HVAC module, and so push button the door to lock it.
    Note: Ensure the lock is fully engaged and the door is sealed shut.
  • Position the front passenger footwell cover on the vehicle and connect the electric harness to the cover.
  • Install the front passenger footwell cover, making certain the magnets (x3) are locked into position.
  • Move the front passenger seat dorsum to its original position.

Back to Pinnacle

 

Checking and Adjusting Tire Pressures

To cheque tire pressures when tires are cold and Model S has been stationary for over three hours, follow these steps:

  • Refer to the 'Tire and Loading Data' characterization located on the driver's center door colonnade for the target tire pressure.
  • Remove the valve cap.
  • Firmly printing an authentic tire pressure approximate onto the valve to measure pressure.
  • If required, add or remove air to reach the recommended pressure.
    Notation: You lot tin can release air by pressing the metal stalk in the middle of the valve.
  • Re-check pressure using the accurate tire guess.
  • Repeat steps three and 4 as necessary until the tire force per unit area is correct.
  • Reinstall the valve cap to prevent clay from entering. Periodically check the valve for damage and leaks.

Back to Meridian

 

Drive to Calibrate Cameras

Model S must maneuver with precision when Autopilot features are beingness used. Therefore, before some features can be used for the showtime fourth dimension or afterward some types of service repairs, cameras must complete a self-calibration process. For your convenience, the musical instrument panel displays a progress indicator.

When scale is complete, Autopilot features are available for use. Calibration typically completes after driving 20-25 miles, merely the distance varies depending on route and environmental weather. For example, calibration completes quicker when driving on a directly route with multiple lanes (such as a controlled-admission highway), with highly-visible lane markings (in the driving lane as well every bit the adjacent lanes). Contact Tesla only if your Model South has not completed the calibration process later driving 100 miles in the described conditions.

If a camera has shifted from its calibrated position (for case, the camera or windshield was replaced), yous must clear the scale. To do so, touch on 'Controls' > 'Service' > 'Camera Calibration' > 'Articulate Scale.' When the scale is cleared, Model Southward repeats the scale process. While this helps re-calibrate the cameras in many cases, 'Clear Calibration' may not resolve all photographic camera and sensor concerns.

Annotation: To calibrate, cameras require highly-visible lane markings in both the driving lane and adjacent lanes (at least ii lanes over on each side of the vehicle). For best results, drive in the middle lane of a multi-lane highway (ideally with at least 5 lanes) that has clear lane markings and minimal traffic.

Annotation: If you attempt to use a feature that is not available until the calibration process is complete, the feature is disabled and the instrument panel displays a message.

Notation: Model South must repeat the calibration procedure if the cameras are serviced by Tesla, and in some cases, after a software update.

Back to Peak

 

Replacing Hood Struts

Your hood struts tin can be replaced if they begin to fail for whatever reason. To supplant your hood struts on Model S, follow these steps:

Back to Top

 

Topping Up Windshield Washer Fluid

The simply reservoir into which you can add together fluid is the windshield washer fluid reservoir, which is located backside the forepart trunk. When the level is low, a bulletin displays on the musical instrument panel.

To top up the washer fluid in Model Due south, follow these steps:

  • Open the hood.
  • Make clean around the filler cap before opening it to forbid dirt from inbound the reservoir.
  • Open the filler cap.
  • While avoiding spilling, make full the reservoir until the fluid level is visible simply below the filler neck.
  • Wipe up any spills immediately and wash the affected area with water.
  • Replace the filler cap.

Note: Some national or local regulations restrict the use of Volatile Organic Compounds (VOCs). VOCs are commonly used as antifreeze in washer fluid. Use a washer fluid with limited VOC content only if it provides acceptable freeze resistance for all climates in which you drive Model S.

Notation: Local regulations may prohibit the utilise of methanol-based washer fluid. Use ethanol-based washer fluid instead.

Caution: Practice not add formulated washer fluids that contain h2o repellent or bug wash. These fluids can cause streaking, smearing and squeaking or other noises.

Warning: In temperatures below 40° F (4° C), use a washer fluid with antifreeze. In cold weather, using a washer fluid without antifreeze tin impair visibility through the windshield.

Warning: Windshield washer fluid tin irritate eyes and skin. Read and observe the instructions provided past the washer fluid manufacturer.

Back to Top

 

Replacing Wiper Blades

For optimum operation, replace the wiper blades at least in one case a yr. Replacement blades for Model S must encounter the post-obit criteria:

  • The bract on the driver'south side must be 26 inches long and 20 inches long for the bract on the passenger's side.
  • Ensure the connector on the replacement blade is the aforementioned every bit the original blade. Unlike connectors may preclude the replacement blade from connecting to the wiper arm on the vehicle.

You can buy replacement wiper blades from the Tesla Store.

Note: Only install replacement blades that are identical to the original blades. Using inappropriate blades can damage the wiper system and windshield.

To replace the wiper blades on Model South, follow these steps:

  • Shift into Park and plow off the wipers.
  • Touch 'Controls' > 'Service' > 'Wiper Service Fashion' > 'ON' to move the wipers to the service position.
  • Lift the wiper arm a short distance away from the windshield, simply far enough to access the wiper bract.

    Caution: Wiper blades do not lock into a lifted position. Do non elevator a wiper arm beyond its intended position.

  • Place a towel between the wiper arm and windshield to avoid scratching or smashing the windshield.
  • Hold the wiper arm and press the locking tab while sliding the blade downwards the arm.
  • Align the new wiper blade on the wiper arm and slide it toward the stop of the wiper arm until it locks into identify.
  • Turn 'Wiper Service Mode' off to return the wipers to their normal position.

Back to Top

 

Manually Releasing Charge Cable

If the usual methods for releasing a charge cable from the accuse port (using the charge handle release button, touchscreen or Tesla app) practice not work, carefully follow these steps:

  • Ensure that Model Due south is not actively charging by displaying the charging screen on the touchscreen. If necessary, touch 'Stop Charging.'
  • Open up the rear torso.
  • Pull the accuse port's release cablevision downwards to unlatch the charge cablevision.

    Warning: Do non pull the release cable while simultaneously attempting to remove the charge cable from the charge port. Always pull the release cable before attempting to remove the accuse cable. Failure to follow these instructions tin can result in electrical daze and serious injury.



    Note: The release cable may be recessed within the opening of the trim.
  • Pull the charge cable from the accuse port.

Caution: Utilise the release cable but in situations where yous can not release the charge cable using the usual methods. Continuous use can damage the release cable or charging equipment.

Warning: Practise not perform this procedure when your vehicle is charging, or if any orange high voltage conductors are exposed. Failure to follow these instructions can result in electric shock and serious injury or damage to the vehicle. If you lot are uncertain as to how to safely perform this process, contact your nearest Service Center.

Back to Acme

 

Opening Hood with No Power

In the unlikely outcome that Model S has no low voltage ability, yous volition be unable to open up the front trunk using the touchscreen, fundamental fob or Tesla app. To open the Model S front trunk in this situation, follow these steps:

Note: The following steps do not open the front trunk if Model S is locked and has low voltage ability.

  • Locate an external low voltage power supply (such as a portable jump starter).
  • Release the tow eye embrace by pressing firmly on the top right perimeter of the cover until it pivots inward, and then gently pulling the raised section toward you.
  • Pull the two wires out of the tow eye opening to expose both terminals.
  • Connect the low voltage power supply'south red positive (+) cablevision to the scarlet positive (+) concluding.
  • Connect the depression voltage power supply'southward black negative (-) cable to the black negative (-) terminal.
    Note: Applying external low voltage ability to these terminals only releases the hood latches. You cannot charge the low voltage battery using these terminals.
  • Turn on the external power supply (refer to the manufacturer's instructions). The hood latches are immediately released and yous can now open the hood to access the front body surface area.
  • Disconnect both cables, kickoff with the blackness negative (-) cable.
  • If pulling the vehicle onto a flatbed truck, do non supplant the tow centre cover all the same. If necessary, install the tow centre cover by inserting the wires into the tow eye opening and aligning the tow eye cover into position and snapping it into place.

Back to Pinnacle

 

Leap Starting the Low Voltage Bombardment

Caution: Model S cannot exist used to jump start another vehicle. Doing so can result in harm.

Note: If bound starting Model S using some other vehicle, refer to that vehicle manufacturer'southward instructions. The following instructions presume an external depression voltage ability supply (such equally a portable bound starter) is used.

Circumspection: Avoid curt circuits when jump starting Model S. Connecting cables to the wrong jump mail, touching leads together, etc., can result in damage to Model Due south.

To jump start Model S, follow these steps:

Back to Top

 

Adjusting Liftgate Opening Height

Y'all can accommodate the opening height of the liftgate to make information technology easier to reach or to avoid low-hanging ceilings or objects (for example, a garage door or light), follow these steps:

  • Open the torso, then manually lower or heighten the liftgate to the desired opening superlative.
  • Press and hold the button on the underside of the liftgate for three seconds until you hear a confirmation chime.
  • Ostend that you have gear up it to the desired summit past closing the liftgate, then reopening it.

Back to Acme

 

Charge Port Status Lights

When your charge port is open the status light changes color to communicate its current country and aid troubleshoot issues in the unlikely event that one comes upwards. Every bit a reminder, the charge port light turns off after a brusk catamenia of time if the vehicle is locked (for example, if y'all walk upwardly to the car later it has been charging for a while).

Notation: When plugging your vehicle in, consider monitoring the colour of the charge port before walking away. If yous see a red or amber calorie-free, troubleshooting the issue before yous exit can ensure a successful charging session.

Color of Accuse Port Low-cal What information technology Means What to Do

WHITE - SOLID

(normal behavior)

 Model South is ready to charge and the connector is non inserted, or the accuse port latch is unlocked and the connector is ready to exist removed. Insert the charge connector if you lot desire to accuse, or remove the charge connector if done charging.

BLUE - BLINKING

(normal beliefs)

 Model S is actively communicating with the charging station. Zippo. Wait a few seconds for the charge port to either brainstorm blinking green (charging) or turn to solid blue (a charging session is scheduled for the future).

BLUE - SOLID

(action may be required)

 Model S detects that a connector has been plugged in and the charging session is scheduled to begin at a specified future time. Not actively charging. If yous want to charge immediately, disable Scheduled Charging or impact 'Start Charging' on the touchscreen or in the Tesla app. If the Scheduled Charging setting is intended, no further activeness is required. As a reminder, Scheduled Charging remembers your location.

GREEN - BLINKING

(normal behavior)

 Charging is in progress. As Model S approaches a full charge, the frequency of the blinking slows. Cipher. Remove the charge cable when yous are washed charging.

GREEN - SOLID

(normal behavior)

 Charging is complete. Remove the charge cable when y'all are ready to bulldoze.

AMBER - SOLID

(action required)

 The connector is not fully plugged in to the accuse port. Realign the connector to the accuse port and insert fully. If the outcome persists, inspect the charge port and connector for obstructions. If no obstructions are found, attempt a different charge cable.

Bister - BLINKING

(activity required)

 Model S is charging at a reduced current because it is not fully plugged in to the charge port. Realign the connector to the charge port and insert fully. If the effect persists, inspect the charge port and connector for obstructions. If no obstructions are found, effort a different charge cable.

Cerise - SOLID

(action required)

 A error is detected and charging has stopped or cannot begin. Check the instrument panel or touchscreen for a fault bulletin. If a fault is not nowadays, endeavour using a dissimilar charge cablevision or resetting the charging source (refer to the status lights on the Mobile Connector or Wall Connector if applicative). If a different charge cable does not piece of work, turn the vehicle off and on using the touchscreen and try again.

NO LIGHT

(normal beliefs)

 Model Southward is locked and has been sleeping for a menstruum of time. Nothing. Unlocking the vehicle or pressing the push button on accuse handle will cause the accuse port condition light to brandish again.

Dorsum to Top

 

Gen 2 Mobile Connector Status Lights

Under normal conditions, when charging is in progress, the Tesla logo lights illuminate sequentially, and the red lite is off. Identify problems by paying attending to these lights.

In some cases, you may need to reset the device by unplugging the Mobile Connector from the vehicle or from the power outlet.

Green Lights Red Low-cal What information technology Means What to Do
All on for ane second Off Showtime-upward sequence. Nothing. The Mobile Connector is starting up.
All on Off Power on. The Mobile Connector is powered and standing by, only not charging. Brand sure the Mobile Connector is plugged into the vehicle.
Streaming Off Charging is in progress. Nothing. The Mobile Connector is successfully charging.
Streaming 1 wink Charging current is reduced due to loftier temperature detected in the vehicle connector. Unplug the Mobile Connector from the vehicle, so plug it dorsum in. Consider charging in a cooler area, such as indoors or in the shade. If the error persists, contact your closest Service Centre.
Streaming 2 flashes Charging electric current is reduced due to high temperature detected in the input plug that connects to the Mobile Connector controller. Unplug the Mobile Connector from both the vehicle and the wall. Ensure that the adapter is fully inserted, plug the Mobile Connector into the wall, and then plug it into the vehicle. If the error persists, contact your closest Service Centre.
Streaming 3 flashes Charging current is reduced due to loftier temperature detected in the Mobile Connector controller. Unplug the Mobile Connector from the vehicle, and and then plug it dorsum in. Consider charging in a cooler area, such equally indoors or in the shade. If the error persists, contact your closest Service Center.
Streaming 4 flashes Charging current is reduced due to high temperature detected in the wall plug. Make certain the power outlet is suitable for charging and that the plug is seated correctly. Consider connecting to a different outlet. If uncertain, enquire your electrician.
Streaming 5 flashes Charging current is reduced due to a detected fault in the adapter. Make sure the Mobile Connector's adapter is fastened properly.
Off 1 flash Footing error. Electric current is leaking through a potentially unsafe path. Unplug the Mobile Connector from the vehicle and then plug it back in. Try a different outlet. If the error persists, contact your closest Service Center.
Off 2 flashes Ground loss. The Mobile Connector detects a loss of basis. Make sure the power outlet is properly grounded. Consider connecting to a unlike outlet. If uncertain, ask your electrician.
Off 3 flashes Relay/contactor mistake. Unplug the Mobile Connector from the vehicle and then plug it back in. Try a unlike outlet. If the error persists, contact your closest Service Eye.
Off 4 flashes Over- or under-voltage protection. Brand sure the ability outlet is suitable for charging and that the plug is seated correctly. Consider connecting to a dissimilar outlet. If uncertain, ask your electrician.
Off 5 flashes Adapter fault. Make sure the Mobile Connector'southward adapter is fastened properly.
Off six flashes Pilot mistake. The airplane pilot level is incorrect. Unplug the Mobile Connector from the vehicle and so plug it back in. Try a different outlet. If the error persists, contact your closest Service Center.
Off 7 flashes Software fault or mismatch. Update the vehicle's software, if bachelor. If an update is non available, contact your closest Service Center.
Off On Self cheque failed. Unplug the Mobile Connector from the vehicle so plug it back in. If the error persists, unplug the Mobile Connector from both the vehicle and the power outlet, then plug information technology back in.
All on i wink Thermal fault. Consider charging in a cooler area, such as indoors or in the shade. If the fault persists, contact your closest Service Center.
All on 5 flashes Adapter error. Charging current is limited to 8A. Unplug the Mobile Connector from the vehicle. Plug the Mobile Connector dorsum into the vehicle. If the error persists, unplug the Mobile Connector from both the vehicle and the power outlet, then plug it back in.
Off Off Ability lost. Unplug the Mobile Connector and cheque that the power outlet has power.

Back to Peak

SHARE